BenQ mobile codes
Language Menu for BenQ-Siemens mobile
English menu:
*#0001#
Deutsch menu:
*#0049#
Secret Code for BenQ
*#0606# remove sim card before
Unlock Sim:
*#0003*(secret code)#
Bonus Screen:
*12022243121
Factory settings:
Type *#9999# to reset factory settings.
LG Mobile Codes
On the main screen type *#06#
Information you get from the IMEI (International Mobile Equipment Identity)
XXXXXX XX XXXXXX X
TAC FAC SNR SP
TAC = Type approval code of your LG Mobile
FAC = Final assembly code of your cellphone
SNR = Serial number of your LG Phone
SP = Spare
Other secret tricks for LG mobile or cellphone
LG all models test mode:
Type 2945#*# on the main screen.
2945*#01*# Secret menu for LG
IMEI and SW (LG 510): *#07#
Software version (LG B1200): *8375#
Recount cheksum (LG B1200): *6861#
Factory test (B1200): #PWR 668
Simlock menu (LG B1200): 1945#*5101#
Simlock menu (LG 510W, 5200): 2945#*5101#
Simlock menu (LG 7020, 7010): 2945#*70001#
Simlock menu (LG 500, 600): 2947#*
LG-U81XX SPECIAL CODES
Code to read phone version :
- Phone without SIM
- Enter 277634#*# or 47328545454#
- Select 'SW Ver.info'
Code to reset phone :
- Phone without SIM
- Enter 277634#*# or 47328545454#
- Select 'Factory Reset'
Code to enter UNLOCK MENU :
- Phone wit SIM inside
- Enter 2945#*88110#
Test Menu 8330 : 637664#*#
Test Menu 8180 V10a: 49857465454#
Test Menu 8180 V11a: 492662464663#
Test Menu 8130-8138: 47328545454#
Test Menu 8110-8120: 277634#*
NOKIA-Mobile Cracking Codes
1 Imagine ur cell battery is very low, u r expecting an important call and u don't have a charger.
Nokia instrument comes with a reserve battery. To activate, key is "*3370#"
Ur cell will restart with this reserve and ur instrument will show a 50% incerase in battery.
This reserve will get charged when u charge ur cell next time.
*3370# Activate Enhanced Full Rate Codec (EFR)-Your phone uses the best sound quality but talk time is reduced by approx. 5%
#3370# Deactivate Enhanced Full Rate Codec( EFR)
*#4720# Activate Half Rate Codec - Your phone uses a lower quality sound
but you should gain approx 30% more Talk Time
*#4720# Deactivate Half Rate Codec
2 *#0000# Displays your phones software version,
1st Line :S oftware Version,
2nd Line : Software Release Date,
3rd Line : Compression Type
3 *#9999# Phones software v ersion if *#0000# does not work
4 *#06# For checking the International Mobile Equipment Identity (IMEI Number)
5 #pw+1234567890+1# Provider Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)
6 #pw+1234567890+2# Network Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)
7 #pw+1234567890+3# Country Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)
8 #pw+1234567890+4# SIM Card Lock Status.(use the "*" button to obtain the "p,w" and "+" symbols)
9 *#147# (vodafone) this lets you know who called you last *#1471# Last call (Only vodofone)
10 *#21# Allows you to check the number that "All Calls" are diverted To
11 *#2640# Displays security code in use
12 *#30# Lets you see the private number
13 *#43# Allows you to check the "Call Waiting" status of your phone.
14 *#61# Allows you to check the number that "On No Reply" calls are diverted to
15 *#62# Allows you to check the number that "Divert If Unrea chable(no service)" calls are diverted to
16 *#67# Allows you to check the number that "On Busy Calls" are diverted to
17 *#67705646#R emoves operator logo on 3310 & 3330
18 *#73# Reset phone timers and game scores
19 *#746025625# Displays the SIM Clock status, if your phone supports this power saving feature "SIM Clock Stop Allowed", it
means you will get the best standby time possible
20 *#7760# Manufactures code
21 *#7780# Restore factory settings
22 *#8110# Software version for the nokia 8110
23 *#92702689# (to rember *#WAR0ANTY#)
Displays -
1.Serial Number,
2.Date Made
3.Purchase Date,
4.Date of last repair (0000 for no repairs),
5.Transfer User Data.
To exit this mode -you need to switch your phone off then on again
24 *#94870345123456789# Deactivate the PWM-Mem
25 **21*number# Turn on "All Calls" diverting to the phone number entered
26 **61*number# Turn on "No Reply" diverting to the phone number entered
27 **67*number# Turn on "On Busy" diverting to the phone number entered
Each command is prefixed with either one or two * or # characters as follows:
** Register and Activate
* Activate
## De-Register (and Deactivate)
# Deactivate
*# Check Status
© Call button
Once each command has been entered, if it is a network command (as opposed to a local handset command) it must be transmitted to the network by pressing the YES (receiver) key which acts as an enter key - this is represented here with the © character. Always enter numbers in full international format +CountryAreaNumber ( e.g. +447712345678).
Command Description Command String
Security
Change call barring code **03*OldCode*NewCode*NewCode#©
Change call barring code **03*330*OldCode*NewCode*NewCode#©
Change PIN code **04*OldPIN*NewPIN*NewPIN#©
Change PIN2 code **042*OldPIN2*NewPIN2*NewPIN2#©
Unlock PIN code (when PIN is entered wrong 3 times) **05*PUK*NewPIN*NewPIN#©
Unlock PIN2 code (when PIN2 is entered wrong 3 times) **052*PUK2*NewPIN2*NewPIN2#©
Display IMEI *#06#
Call Forwarding (Diversions)
De-register all call diversions ##002#©
Set all configured call diversions to number and activate **004*number#©
De-register all configured call diversions (no answer, not reachable, busy) ##004#©
Unconditionally divert all calls to number and activate **21*number#©
Activate unconditionally divert all calls *21#©
De-register unconditionally divert all calls ##21#©
Deactivate unconditionally divert all calls #21#©
Check status of unconditionally divert all calls *#21#©
Divert on no answer to number and activate **61*number#©
Activate divert on no answer *61#©
De-register divert on no answer ##61#©
Deactivate divert on no answer #61#©
Check status of divert on no answer *#61#©
Divert on not reachable to number and activate **62*number#©
Activate divert on not reachable *62#©
De-register divert on not reachable ##62#©
Deactivate divert on not reachable #62#©
Check status of divert on not reachable *#62#©
Divert on busy to number and activate /td> **67*number#©<
Activate divert on busy *67#©
De-register divert on busy ##67#©
Deactivate divert on busy #67#©
Check status of divert on busy *#67#©
Change number of seconds of ringing for the given service before diverting a call (such as on no answer). Seconds must be a value from 5 to 30. De-registering the same divert will also delete this change! **service*number**seconds#© (Service numbers, see below)
Call barring
Activate barr all outgoing calls (see Security to set code) **33*code#©
Deactivate barr all outgoing calls #33*code#©
Check status of barr all outgoing calls *#33#©
Activate barr all calls **330*code#©
Deactivate barr all calls #330*code#©
Check status of barr all calls /td> *#330*code#©<
Activate barr all outgoing international calls **331*code#©
Deactivate barr all outgoing international calls #331*code#©
Check status of barr all outgoing international calls *#331#©
Activate barr all outgoing international calls except to home country **332*code#©
Deactivate barr all outgoing international calls except to home country #332*code#©
Check status of barr all outgoing international calls except to home country *#332#©
Activate barr all outgoing calls **333*code#©
Deactivate barr all outgoing calls #333*code#©
Check status of barr all outgoing calls *#333#©
Activate barr all incoming calls **35*code#©
Deactivate barr all incoming calls #35*code#©
Check status of barr all incoming calls *#35#©
Activate barr all incoming calls when roaming **351*code#©
Deactivate barr all incoming calls when roaming #351*code#©
Check status of barr all incoming calls when roaming *#351#©
Activate barr all incoming calls **353*code#©
Deactivate barr all incoming calls #353*code#©
Check status of barr all incoming calls *#353#©
Call waiting
Activate call waiting *43*#©
Deactivate call waiting #43##©
Check status of call waiting *#43#©
Calling Line Identification
The following only works if CLIP and CLIR are enabled (ask your service provider)
CLIP: Presentation of the number of the incoming call
Activate CLIP **30#©
Deactivate CLIP ##30#©
Check status of CLIP *#30#©
CLIR: Presentation of one's own number to the to the called party
Activate CLIR **31#©
Activate CLIR for the actual call *31#number©
Deactivate CLIR ##31#©
Deactivate CLIR for the actual call #31#number©
Check status of CLIR *#31#©
COLP: Presentation of the actual number reached (if number called was diverted to another number
Activate COLP *76#©
Deactivate COLP #76#©
Check status of COLP *#76#©
COLR: Presentation of the original number called by the calling party (if the call was diverted to this cellphone)
Activate COLR *77#©
Deactivate COLR #77#©
Check status of COLR *#77#©
Nokia Mobile Secret Codes-part1
Nokia 31xx
____________
Firmware version
*#0000# or *#3110#
IMEI Code
*# 06 #
Restores Factory Settings
*#7780#
Warranty Codes
*#92702689# (= *#war0anty#)
Just scroll down through the information. If entering the above code requires a
further warranty code try entering the following:
6232 (OK) : Month and year of manufacture
7332 (OK) : Last repair date
7832 (OK) : Purchase date (if previously set)
9268 (OK) : Serial number
37832 (OK) : Set purchase date (this can only be done once)
87267 (OK) : Confirm transfer
Nokia 5110
_____________
IMEI Number *#06#
For checking the IMEI (International Mobile Equipment Identity).
---------------------------------------------------------
Security Code 12345
Default security code is 12345. If you forgot your security code, there s so many program on the net which allowed you to know the security code likes Security ID Generator, Nokia IMEI Changer, etc.
update:
Security ID Generator (SID.EXE) and IMEI Generator (NOKIAIMEI.EXE) doesn t works with Nokia 5110
Resetting Security Code
If you accidentally lock the phone or forgot the security code, the best thing to do is check it with your local Nokia dealer. For advanced user, you can use WinTesla, PCLocals or LogoManager program to read the security code or resetting the code (You will need an FBUS/MBUS (or compatible) cable to do this.
---------------------------------------------------------
Software Version *#0000#
For checking the phones software (SW) - called firmware revision information.
e.q : Version V. 4.51 (26-03-98) will display
V 04.51
26-03-98
NSE-1
first line:
The Software Version (my guess is that this software has been used in previously Nokia-phones, what do you say?!).
second line:
The Date of the SW release.
third line:
NHE-8 has something to do with the type of phone you are dealing with. Is it GSM 900 (standard), GSM 1800 (DCS1800) or GSM 1900 (PCS1900)?
Nokia 2110, 3110, 8110(i) are all NHE types. The only thing that vary is the code after NHE- ("8").
NHE = GSM 900, NHK =GSM 1800 - The number in the end = the model (2110i = 4 etc.)
The 5110 and 6110 is called NSE-1 and NSE-3...this may be because it supports EFR (?)
update:
Newest Software Version was V5.22 (xx-xx-99)
V 05.22
01-07-99
NSE-1
If your software version is V4.00, upgrade your software version to latest version. V4.00 contains bugs that sometimes will show message,
"SIM Card Not Ready" even the card is already inside the phone.
---------------------------------------------------------
Software Update
The only thing to do (for you and me) is for us to go to the nearest Nokia dealer and make him do it for you. Just remember that it is supposed to be free (a receipt is required) so don t let him tell you anything else!
---------------------------------------------------------
SIM clock *#746025625# [*#sim0clock#]
to check if the Sim-Clock can be Stopped. This option is depen on your service provider network. (Sim-clock-stop is a kind of standby mode which will save battery time)
update:
This code doesn t work on phone with software version 4.59.
---------------------------------------------------------
Waranty Code *#92702689# [*#war0anty#]
Menu:
Displays Serial Number.
Displays the Month and Year of Manufacture (0698)
Displays (if there) the date where the phone was purchased (MMYY) you can here set the Purchasing Date
(Warning: You can only do this once - so be careful what you write)
Displays the date of the last repairment - if found (0000)
The next screen has Transfer User Data? (the same option as the 8110)
To exit turn the phone off and then back on.
---------------------------------------------------------
SP Lock The Service provider (SP) lock
Is used to lock the cell phone to the SP s SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it!
The cell phone will however accept another SIM card from the same operator.
All Nokia phones (2110 and newer) have four different SIM locks which can be used to lock the phone for up to 4 different providers. But most phones with restriction only have one lock activated. ( lock 1)
The main code used in Nokia phones is:
#pw+(master code)+Y#
This code is able to check, activate or remove Sim card restriction (SP-lock).
Use the * key to get the p, + and w chars.
Y has to be 1,2,3 or 4 - depending of what lock you what to deal with.
#pw+1234567890+1# for Provider-Lock status
#pw+1234567890+2# for Network-Lock status
#pw+1234567890+3# for Provider(???)-Lock status
#pw+1234567890+4# for SimCard-Lock status
(master code) is a 10 digit code, based on the phones IMEI number.
(I can NOT give you the master code SO DON T ASK ME FOR IT! )
Please click here to learn more about how to obtain mastercode and find out the lock status of your phone
eq. To remove restriction on lock 1 type following code:
#pw+(master code)+1#
If you just want to check your phone use 10 random numbers Eg. 1234567890 as the (master code)
eq. To check if phone if restricted on lock 1 type the following code:
#pw+1234567890+1#
Please NOTE that these codes could be used with care!
A user told me that it s only possible to type in about 3 different codes on each lock! Then something bad will happen ..therefore be careful!
---------------------------------------------------------
How can I check what locks have my phone closed?
There is 2 methods:
Use winlock to see the state of the locks, pressing Read Info.The Counter is the number of times that you have tried unlock your phone using an incorrect master code.
You can check it entering an imaginary mastercode on your phone but, it s not recommended because if you try enter a code 5 times your phone will not work anymore. By example, if you press at your phone #pw+1234567890+2# (note that # , p , w and + characters must be selected from * key) and your phone give you Code Error then your phone have lock 2 closed, if you get the message SIM Restriction Off your phone have lock 2 opened.
Look the table above to see how can check all locks:
Lock number Description Sequence to Check
1 Provider Lock #pw+1234567890+1#
2 Network-Lock #pw+1234567890+2#
3 Another Provider Lock #pw+1234567890+3#
4 SIM Card Lock #pw+1234567890+4#
---------------------------------------------------------
Unlock SP-Lock
Here is a way to Unlock your phone which is Service Provider locked, without to know SPLock code. With a Nokia 16xx/21xx/31xx/51xx/81xx that are SIMlocked to one privider you can bypass the SP lock like this:
First of all, PIN CODE MUST BE ON, then press:
C
C and hold until it clears display
* and hold until start to blink
* and hold until start to blink
04***your pin>#
Each time you turn your phone OFF it resets the lock, so this need to be done each time you ll turn your phone ON
The phone now says: PIN CODE CHANGED (or ACCEPTED)
and the SIM card is accepted until you restart the phone again.
NOTE: On vesion 5.04 Nokia has removed this option !
update:
There s another Nokia service provider lock generator for DOS (somehere on the net) called 5161un.zip (for Nokia 51xx-61xx models) This program uses the #pw+(master code)+1# code to unlock the phone. With this software you need to have a access to the eeprom.. Sad
---------------------------------------------------------
Bypass the SP-lock
With a Nokia 16xx/21xx/31xx/51xx/81xx that are SIM locked to one privider you can bypass the SP lock like this:
Insert sim card of diferent provider.
Turn on the phone and press the UP VOLUME key for 3 sec. then release it and the phone says PIN CODE ?
Press the "C" key.
Then Press * and wait until it desapear and apear again, then press * one more time and 04*PIN*PIN*PIN#
The phone now says: PIN CODE CHANGED (or ACCEPTED)
and the SIM card is accepted until you restart the phone again.
update:
On version 5.04 Nokia has removed this option !
---------------------------------------------------------
How to open lock 1 and 4?
You will need Winlock software and MBUS cable to do this. Winlock is a Nokia service program that you can use to open lock 1 and 4, really you are closing locks when you do that, but when you write ????? at MCC+MNC and MSIN text box, the phone don t understand it and consider that it s open.
That trick only works for lock 1 and 4, but not for lock 2 and 3. If you did not know your lock type, please read our miscellaneous tips page first. or read at above section in this page.
Install winlock 1.10
Connect your MBUS nokia data cable
Run Winlock
Push Read Phone, if you have Lock 2 or Lock 3 closed you can not open your phone, but you can try change Lock 2.
Select State Close in Lock 1 and Lock 4, fill out MCC+MNC and MSIN text boxes with ??????? and Push Close Locks.
Now you can use any operator card in your phone. If you get any error when you do that do the following steps:
Select State Automatic in Lock 1 and Lock 4 and change type to User in Lock 1 and Lock 4, fill out MCC+MNC and MSIN text boxes with ?????????? and Push Close Locks.
Select State Automatic in Lock 1 and Lock 4 and change type to Factory in Lock 1 and Lock 4, fill out MCC+MNC and MSIN text boxes with ?????????? and Push Close Locks.
If you continue getting errors you must turn off your phone and reset computer and try again.
---------------------------------------------------------
How to open lock 2?
When operators companies close lock2 you can only use the contract or prepaid card for this operator, but you can use another operator company prepaid card if you know what GID1 must write.
Install Winlock
Run Winlock
Configure Winlock. Select menu Winlock->Defaults and change GID byte count to 2.
Push Read Phone, and write down GID1 info that appear in lock 2.
Insert the prepaid card from a different operator company.
We must find out a the GID1 info adecuate for our new prepaid or contract card, take a look at our GID1 list and check if your operator and SIM card type is included, if not try to get a phone that have lock 2 closed and have the SIM card type that you want to use in your phone, and read GID1 info with winlock. You can try to write the most used GID1 codes like 0000,10FF,01FF, or FFFF, etc.
Change Lock 2 Type from User To Factory or from Factory to User.
Push Close Locks
Your phone will be reset every time you push Close Locks, if your card is not acepted the GID1 is not correct, repeat from step 4 until you find the correct GID1.
If you get error you must turn off your phone and reset computer and try again.
If you want your phone accept your original prepaid card write in GID1 the code you read at step 2 and close locks.
Exist a GID1 list?
In addition to the official way to open locks that Nokia service centers use with TDB4 or TDF-4(for WinTesla) security boxes, there is two secrets methods:
Opening the phone and adding a chip inside phone motherboard. But you will loose any warranty of your phone.
Using a special software with a MBUS Nokia cable. I don t have this software. Please don t bother me asking me about that. The only thing i know about that is that a friend is removing lock 2 using a special software. He don t make this for money, only for fun.
--------------------------------------------------------
Main Code #pw+(master code)+Y#
This code is able to check, activate or remove Sim card restriction (SP-lock).
Use the * key to get the p, + and w chars.
Y has to be 1,2,3 or 4 - depending of what lock you what to deal with.
#pw+1234567890+1# for Provider-Lock status
#pw+1234567890+2# for Network-Lock status
#pw+1234567890+3# for Provider(???)-Lock status
#pw+1234567890+4# for SimCard-Lock status
(master code) is a 10 digit code, based on the phones IMEI number.
update:
I get report that told me the code didn t works for Optimus Card
---------------------------------------------------------
Enhanced Full Rate Codec (EFR)
Enhanced Full Rate will give you much better sound quality when you enable it. The new Enhanced Full Rate CODEC adopted by GSM uses the ASELP (AlgebraicCode Excitation Linear Prediction) compression technology. This technology allows for much great voice quality in the same number of bits as the older Full Rate CODEC. The older technology was called LPC-RPE (Linear Prediction Coding with Regular Pulse Excitation). Both operate at 13 kilobits.(but you take up more space on the network, so they can charge you more)
*3370# and EFR will be activated after a reboot of the phone ( consumes more power )
#3370#
and EFR will be switched off after a reboot of the phone.
---------------------------------------------------------
Half Rate Codec (HR)
Half Rate will give you bad sound quality, which gives the service provider the opportunity to have more calls on the network; and you might get a lower charge from them. (Will give you 30% longer talk-time)
*4720# Half Rate coded will be activated after a reboot of the phone ( better standby time )
#4720# Half Rate coded will be de-activated after a reboot of the phone
---------------------------------------------------------
Unblocking Code
Unblock PIN1 : **05*PUK*newPIN1*newPIN1#@
UnBlock PIN2 : **052*PUK2*newPIN2*newPIN2#@
---------------------------------------------------------
Hiding your phone number
Dial 141 then the number you want to call eg. 141#######
This should stop your number been sent to the caller. (*)
(*) This only works on UK phones, if anybody has tried this and works, please let me know.
---------------------------------------------------------
Unlocking PIN2 for software version
V 05.07
20.11.98
NSE-1
If your SimCard is locked by your SP, you can check it and if it is, you will get the "wrong code" message on the display (for use 1234567890)
If your SimCard is locked by your SP, you can t unlock PIN2 !
---------------------------------------------------------
Blocking phone number at Cantel AT&T
If you have one of those cantel at&t phones if you press #0000# you can block your number
at no extra charge.
---------------------------------------------------------
New Menu on Emergency Calls *3001#12345#
Brings a new menu that gives you access to the emergency calls ( 911 Etc. ). It will give you FREE calls! (only the ones you put in the emergency!! )
This option will depend on your GSM operator
---------------------------------------------------------
Your number in your display
Goto menu 3-7 Call cost settings.
Turn ON the Call costs limit 3-7-1. PIN2 code Required.
Put in the limit with the phone number.
eg. my phone # is 019 2184697
Enter the limit as 2184697
Goto menu 3-7-2 Show costs in. PIN2 code Required.
Select Currency.
Enter Unit price : 1
Enter Currency name as 019 (per my phone # eg. above)
Now the phone number 019 2184697 will remains on the 4th row of the display.
Secondly, if you press the # key, it prompt which line to be used; Line 1 or 2.
---------------------------------------------------------
Free Call Tip
The tips needs Net Monitor enabled. Be aware that the trick will remove Netmonitor in some sw versions like v4.73 and v5.04.
Launch the Net Monitor in your Nokia 51xx / 61xx
Execute the test number 497
Free calling for about 90 sec should now have been activated.
---------------------------------------------------------
Nokia 5110 PIN-Out
Pin-Outs: Bottom view, keyboard up, counting from the left
V V 1 2 3 4 5 6 V
(o) | | [= = = = = =] | |
7 8 9 10 11 12
1 - VIN CHARGER INPUT VOLTAGE 8.4V 0.8A
2 - CHRG CTRL CHARGER CONTROL PWM 32Khz
3 - XMIC MIC INPUT 60mV - 1V
4 - SGND SIGNAL GROUND
5 - XEAR EAR OUTPUT 80mV - 1V
6 - MBUS 9600 B/S
7 - FBUS_RX 9.6 - 230.4 KB/S
8 - FBUS_TX 9.6 - 230.4 KB/S
9 - L_GND CHARGER / LOGIC GND
Nokia 61xx
__________
Firmware version
*#0000# or *#61x0#
IMEI Code
* # 06 #
Warranty Codes
*#92702689# (= *#war0anty#)
Just scroll down through the information. If entering the above code requires a
further warranty code try entering the following:
6232 (OK) : Month and year of manufacture
7332 (OK) : Last repair date
7832 (OK) : Purchase date (if previously set)
9268 (OK) : Serial number
37832 (OK) : Set purchase date (this can only be done once)
87267 (OK) : Confirm transfer
Enhanced Full Rate (EFR) and Half Rate Mode (HFR)
*3370# to activate Enhanced Full Rate - Makes calls sound better, but
decreases the battery life by about 5%.(I recommend this one)
#3370# to deactivate Enhanced Full Rate
*4720# to activate Half Rate Mode - Drops call quality, but increases battery
life by about 30%.
#4720# to deactivate Half Rate Mode
Nokia 81xx
_____________
Show IMEI code
* # 06 #
Software Version
* # 8110 #
This code shows you software version, date of manufacture and hardware number of your phone.
Warranty Codes
*#92702689# (= *#war0anty#)
Just scroll down through the information. If entering the above code requires a
further warranty code try entering the following:
6232 (OK) : Month and year of manufacture
7332 (OK) : Last repair date
7832 (OK) : Purchase date (if previously set)
9268 (OK) : Serial number
37832 (OK) : Set purchase date (this can only be done once)
87267 (OK) : Confirm transfer
Sim Clock information
To check if the Sim-Clock can be stopped type: *#746025625# (= *#sim0clock#)
Nokia 8810
____________
Firmware version
*#0000# or *#8810#
IMEI Code
* # 06 #
Warranty Codes
*#92702689# (= *#war0anty#)
Just scroll down through the information. If entering the above code requires a
further warranty code try entering the following:
6232 (OK) : Month and year of manufacture
7332 (OK) : Last repair date
7832 (OK) : Purchase date (if previously set)
9268 (OK) : Serial number
37832 (OK) : Set purchase date (this can only be done once)
87267 (OK) : Confirm transfer
Enhanced Full Rate (EFR) and Half Rate Mode (HFR)
*3370# to activate Enhanced Full Rate - Makes calls sound better, but
decreases the battery life by about 5%.(I recommend this one)
#3370# to deactivate Enhanced Full Rate
*4720# to activate Half Rate Mode - Drops call quality, but increases battery
life by about 30%.
#4720# to deactivate Half Rate Mode
Motorola Secret Codes
Code to lock keys. Press together *7
Note: [] (pause) means the * key held in until box appears.
Select phone line - (use this to write things below the provider name):
[] [] [] 0 0 8 [] 1 []
Add phonebook to main menu:
[] [] [] 1 0 5 [] 1 []
Add messages to main menu:
[] [] [] 1 0 7 [] 1 []
Copy SIM memory (phonebook menu):
[] [] [] 1 0 8 [] 1 []
Eng Field options (main menu):
[] [] [] 1 1 3 [] 1 []
Slow (Frequency of search menu):
[] [] [] 1 0 1 [] 1 []
Medium (Frequency of search menu):
[] [] [] 1 0 2 [] 1 []
Fast (Frequency of search menu):
[] [] [] 1 0 3 [] 1 []
Enable EFR:
[] [] [] 1 1 9 [] 1 []
Function :
[] [] [] # # # [] 1 []
Change pin:
[] [] [] 0 0 4 [] 1 []
Unblocking using the "puk" number:
[] [] [] 0 0 5 [] 1 []
There are lots of similar codes exist. If you change the last number to 0 you can deactive that code. The 3 digit number at the middle are from 0 to 999. I put the most interesting codes. (EFR):Enhanced Full Rate Codec.
You can change GSM frequencies to 900/1800 by entering the enginnering model. Following the below steps:
enter menu and press 048263* quickly, then you will enter the secret engineering menu
under "Opcode"
input 10*0*3 for GSM 900
10*0*4 for GSM 1800
10*0*5 for GSM 1900
10*0*6 for dual band GSM 900/1800
10*0*7 for dual band GSM 850/1900
To add extra message space 4 your Motorola C350 C450 C550 or C650, press menu button, press 048263* quickly, then on the popup menu enter 47 press ok.press 50 and ok.press 1 ok.press 64 ok.press 1 ok.press 186 and ok.You will receive an extra 50 msgs memory space.Switch phone off and back on.
Nokia All Codes-Part3
Scroll Down to view Specific Model Numbers!!!!
*** WARNING: Using secret codes may be harmful to your phone and result in disabling or worse. Use these codes at your own discretion, we accept no responsiblility for blocked pones while using these codes!!!
IMEI Number
*#06# Cells Identity Code (IMEI = International Mobile Equipment Identity)
XXXXXX XX XXXXXX X
TAC FAC SNR SP
TAC = Type Approval Code (first 2 digits = country code of the approval-country )
FAC = Final Assembly Code: (01,02 = AEG)
(10,20 Nokia)
(40,41,44 Siemens)
(30 Ericsson)
(50 Bosch)
(51 Sony,Siemens,Ericsson)
(60 Alcatel)
(65 AEG)
(70 Sagem)
(75 Dancall)
(80 Philips)
(85 Panasonic)
SNR = Serial Nr.
SP = Spare (always "0")
Software Version
*#0000# shows the software version
Signal Processing
*3370# - Enchanced full Rate Codec (EFR) activation. It will automatically restart.
#3370# - Enchanced full Rate Codec (EFR) deactivation
*4720# - Half Rate Codec activation. It will automatically restart.
#4720# - Half Rate Codec deactivation
Enchanced Full Rate will give you much better sound quality when you enable it. The new Enhanced Full Rate CODEC adopted by GSM uses the ASELP (AlgebraicCode Excitation Linear Prediction) compression technology. This technology allows for much great voice quality in the same number of bits as the older Full Rate CODEC. The older technology was called LPC-RPE (Linear Prediction Coding with Regular Pulse Excitation). Both operate at 13 kilobits.(but you take up more space on the network, so they can charge you more) - Talk-time is reduced with about 5%
Sim Clock Stopping
*#746025625#
[*#sim0clock#]
Checks if the sim clock can be stopped. Sim clock stop is a kind of stand-by mode which will save battery time. This code doesn't work with software version 4.59.
It will tell you if it can be stopped or not.
Warrenty Menu
*#92702689# takes you to a secret menu with 6 choices:
[*#war0anty#]
1. Displays Serial Number.
2. Displays the Month and Year of Manufacture (0997).
3. Displays (if there) the date where the phone was purchased (MMYY).
4. Displays the date of the last repairment - if found (0000).
5. Makes you capable of transferring user data if you have the gear for it.
6. Shows how long the phone has been used to talk. This counter is not reset by when you "clear timers" like the counters in the call register.
Bypass the SP lock With a Nokia 16xx/21xx/31xx/51xx/81xx
1. Insert SIM card of different provider.
2. Turn on the phone and press the UP VOLUME key for 3 sec.
Then release it and the phone says PIN CODE?
3. Press the "C" key.
4. Then Press * and wait until it disappears and appears again, then press * one more time and 04*PIN*PIN*PIN#
Nokia Speed Trap Detector Urban Legend spread by Nokia Engineers ;^)
The settings for radar speed traps detector. Your Nokia cell phone can be programmed to pick up radar speed traps, when programmed your cell phone picks up the radar and alerts you on the message alert tone. ( Doesn't work with Nokia 7110! )
1. Enter your menu
2. Select settings
3. Select security settings
4. Select closed user group
5. Select on
6. Enter 00000
7. Press ok
8. Clear back to normal, within a few seconds your phone will display a radar sign with five zero's next to it. It is now activated.
Unfortunately only Nokia phones have this function. The Cell Phone info display needs to be de-activated. Settings -> Phone Settings -> Cell Info display. Each time you turn off your phone, or even each time you loose contact with your carrier, you'll have to activate it again... It is done using steps 1 through 5 above, but the number (00000) will be already on the field as a default.
The James Bond Trick
If you short-circuit the left middle and right pins on the bottom of the phone with all connections touching each other, the Nokia software hangs! The profile "Headset" will be activated. Before you do this just activate the "Automatic Answer" in the headset profile and set the ringing volume to "Mute". Now you can use your phone for checking out what people are talking about in a room. Just place it under a table in a room and call it. The phone receives the call without ringing and you can listen to what people are saying! Network Monitor
There is a hidden menu inside your Nokia phone. If you want to activate it, you'll have to re-program some chips inside of your phone.
Check your software version. You can only continue if you have v4.33, v4.73 or v5.24.
Take apart the phone.
De-solder the EEPROM (ATMEL AT 24C64)
Read out the data with an EEPROM programmer and save it to a file (Backup)
If you have v.33 or v4.73, change the address "03B8" from "00" to "FF"
If you have v5.24 then change the address "0378" from "00" to "FF"
Write the new data to the EEPROM and solder it back to the phone
Power on your phone and you should have "Netmonitor" enabled.
The Network Monitor gives you the following information:
Carrier number, MS RX Level in DBM, Received signal quality, MS TX power level, C1 (Path loss criterion, used for cell selection and reselection). The range is -99 to 99, RTL (Radio link timeout), Timeslot, Indication of the transmitter status, Information on the Network parameters, TMSI (Temporary Mobile Subscriber Identity), Cell identification (Cell ID, Number of cells being used), MCC (Mobile country code), MCN (Mobile network code), LAC (Location area code), Ciphering (On/Off), Hopping (On/Off), DTX (On/Off), Discard cell barred information.
Game Hacking with Blizzard
Get the file called the 'BlizzardN-GAGE.SIS' from IRC get in #mediaplace on Efnet (note: Downloading cracked/Hacked games is illegal unless you already own a copy of game)
The Blizzard Nokia N-Gage Installer.
1. Unpack Blizzard.sis file that you get from mIRC
2. Transfer the .sis file to your N-Gage
3. Get the .blz (N-gage ROM) from mIRC
4. copy the file to the root dir of your MMC (16MB MMC)Multimedia Card
5. Use the Blizzard application to unpack the .blz file
6. After unpacking the sonic icon should appeared in the MENU
7. Clicked sonic icon and it should work !
List of compatible games for the 3650,6600 and the N-gage that work:
[3650]
SonicN (v.2.5+)
Puyo Pop (v.2.5+)
[6600]
SonicN
Puyo Pop
Pandemonium
Tomb Raider
Super Monkey Ball
Tony Hawks Pro Skater
[N-Gage]
SonicN
Puyo Pop
Pandemonium
Tomb Raider
Super Monkey Ball
Tony Hawks Pro Skater
GSM Network Services Command Strings
When various network functions are selected via the cellphone's menu using the keypad, the cellphone automatically generates the corresponding GSM network command string and transmits it to the network. These commands can however be manually entered via the keypad.
Each command is prefixed with either one or two * or # characters as follows:
** Register and Activate
* Activate
## De-Register (and Deactivate)
# Deactivate
*# Check Status
© Call button
Once each command has been entered, if it is a network command (as opposed to a local handset command) it must be transmitted to the network by pressing the YES (receiver) key which acts as an enter key - this is represented here with the © character. Always enter numbers in full international format +CountryAreaNumber ( e.g. +447712345678).
Command Description Command String
Security
Change call barring code **03*OldCode*NewCode*NewCode#©
Change call barring code **03*330*OldCode*NewCode*NewCode#©
Change PIN code **04*OldPIN*NewPIN*NewPIN#©
Change PIN2 code **042*OldPIN2*NewPIN2*NewPIN2#©
Unlock PIN code (when PIN is entered wrong 3 times) **05*PUK*NewPIN*NewPIN#©
Unlock PIN2 code (when PIN2 is entered wrong 3 times) **052*PUK2*NewPIN2*NewPIN2#©
Display IMEI *#06#
Call Forwarding (Diversions)
De-register all call diversions ##002#©
Set all configured call diversions to number and activate **004*number#©
De-register all configured call diversions (no answer, not reachable, busy) ##004#©
Unconditionally divert all calls to number and activate **21*number#©
Activate unconditionally divert all calls *21#©
De-register unconditionally divert all calls ##21#©
Deactivate unconditionally divert all calls #21#©
Check status of unconditionally divert all calls *#21#©
Divert on no answer to number and activate **61*number#©
Activate divert on no answer *61#©
De-register divert on no answer ##61#©
Deactivate divert on no answer #61#©
Check status of divert on no answer *#61#©
Divert on not reachable to number and activate **62*number#©
Activate divert on not reachable *62#©
De-register divert on not reachable ##62#©
Deactivate divert on not reachable #62#©
Check status of divert on not reachable *#62#©
Divert on busy to number and activate /td> **67*number#©<
Activate divert on busy *67#©
De-register divert on busy ##67#©
Deactivate divert on busy #67#©
Check status of divert on busy *#67#©
Change number of seconds of ringing for the given service before diverting a call (such as on no answer). Seconds must be a value from 5 to 30. De-registering the same divert will also delete this change! **service*number**seconds#© (Service numbers, see below)
Call barring
Activate barr all outgoing calls (see Security to set code) **33*code#©
Deactivate barr all outgoing calls #33*code#©
Check status of barr all outgoing calls *#33#©
Activate barr all calls **330*code#©
Deactivate barr all calls #330*code#©
Check status of barr all calls /td> *#330*code#©<
Activate barr all outgoing international calls **331*code#©
Deactivate barr all outgoing international calls #331*code#©
Check status of barr all outgoing international calls *#331#©
Activate barr all outgoing international calls except to home country **332*code#©
Deactivate barr all outgoing international calls except to home country #332*code#©
Check status of barr all outgoing international calls except to home country *#332#©
Activate barr all outgoing calls **333*code#©
Deactivate barr all outgoing calls #333*code#©
Check status of barr all outgoing calls *#333#©
Activate barr all incoming calls **35*code#©
Deactivate barr all incoming calls #35*code#©
Check status of barr all incoming calls *#35#©
Activate barr all incoming calls when roaming **351*code#©
Deactivate barr all incoming calls when roaming #351*code#©
Check status of barr all incoming calls when roaming *#351#©
Activate barr all incoming calls **353*code#©
Deactivate barr all incoming calls #353*code#©
Check status of barr all incoming calls *#353#©
Call waiting
Activate call waiting *43*#©
Deactivate call waiting #43##©
Check status of call waiting *#43#©
Calling Line Identification
The following only works if CLIP and CLIR are enabled (ask your service provider)
CLIP: Presentation of the number of the incoming call
Activate CLIP **30#©
Deactivate CLIP ##30#©
Check status of CLIP *#30#©
CLIR: Presentation of one's own number to the to the called party
Activate CLIR **31#©
Activate CLIR for the actual call *31#number©
Deactivate CLIR ##31#©
Deactivate CLIR for the actual call #31#number©
Check status of CLIR *#31#©
COLP: Presentation of the actual number reached (if number called was diverted to another number
Activate COLP *76#©
Deactivate COLP #76#©
Check status of COLP *#76#©
COLR: Presentation of the original number called by the calling party (if the call was diverted to this cellphone)
Activate COLR *77#©
Deactivate COLR #77#©
Check status of COLR *#77#©
Cellphone Services
10 All types of cellphone services
11 Speech service
12 Data service
13 Fax
14 Datex-J
15 Teletex
16 Short message service (SMS)
18 All data services without SMS
19 All cellphone services without SMS
Carrier Services
20 All services
21 All asynchronous services
22 All synchronous services
23 3.1kHz services
24 Synchronous point-to-point connections including PAD's (all synchronous data services)
25 Asynchronous point-to-point connections including PAD's (all asynchronous data services)
26 Data packet sending including PAD's (all synchronous data packet services)
27 Services with PAD-share
29 Digital connection with 12kbps
GSM Network Service Codes
Note that at present only the following service codes are in use:
11 Speech
13 fax
25 data
Cell Broadcast
While Short Message Service (SMS) can be configured as a personal service, Cell Broadcast is a general service which is designed for subscribers of a specific cell or topic. For example, a subscriber to cell 050 in England will receive information on the GSM tower currently being used by their phone. This new concept brings a whole new meaning to the term mobile communications as the phone is now able to receive information such as share prices or weather updates without the need of data cards and computers. At present the following message types exist (note: this may vary from carrier to carrier and some carriers may charge for this service):
Code Title
000 Index
010 Flashes
020 Hospitals
022 Doctors
024 Pharmacy
030 Long Distant Road Reports
032 Local Road Reports
034 Taxis
040 Weather
050 District
052 Network Information
054 Operator Services
056 Directory Inquiries (national)
057 Directory Inquiries (international)
058 Customer Care (national)
059 Customer Care (international)
In the future one will be able to control each individual call by use of the following service codes. To do this the user has to insert the service code in front of the last # in the MMI command above.
Or More
Secret Codes for some Nokia models
Nokia 9000/9000i
To view IMEI number *#06#
To view Software Version enter *#8110# Latest Version is under Phone Info.
To view Week and Year of manufacture enter *#3283#
Nokia 9110
*#06# for checking the IMEI (International Mobile Equipment Identity)
*#0000# shows the SW version.
Latest software version: v5.02 (26-08-99)RAE-2
Nokia 7110
*#06# for checking the IMEI (International Mobile Equipment Identity)
*#0000# To view Software Version.
*#3370# - Enhanced Full Rate Codec (EFR) activation. It will automatically restart.
*#3370* - Enhanced Full Rate Codec (EFR) deactivation. It will automatically restart.
*#4720# - Half Rate Codec activation. It will automatically restart
*#4720* - Half Rate Codec deactivation. It will automatically restart
*#746025625# - Sim clock allowed status.
*#92702689# [*#war0anty#] - takes you to a secret menu with 6 choices:
1. Displays Serial Number.
2. Displays the Month and Year of Manufacture (0997)
3. Displays (if there) the date where the phone was purchased (MMYY)
4. Displays the date of the last repairment - if found (0000)
5. makes you capebel of transferring user data if you have the gear for it
6. shows how many hours the phone has been on
Latest software version: 4.77 25-01-00 NSE-5 - EFR and half rate codes do not work with these version.
V 4.76 13-01-00 NSE-5
V 4.75 07-01-00 NSE-5
V 4.73 15.11.99 NSE-5
Nokia 6190
*#06# for checking the IMEI (International Mobile Equipment Identity)
*#6190# shows the SW version.
*#92772689# (after removing the analog module) shows service menu.
*3001#12345[OK] to enter test mode.
*#639# to change NAM.
Nokia 3810
To view IMEI number *#06#
To view Software Version enter *#3810#
Nokia 6120 / 6160 / 6162 (TDMA phones)
*#92772689# for checking ISDN number.
*3001#12345# for field test mode and nam selection and some other stuff...
*#9999# shows the SW version
Nokia 3210 Secret Codes
Nokia 3210
*#06# for checking the IMEI (International Mobile Equipment Identity) Information you get from the IMEI:
XXXXXX XX XXXXXX X
TAC FAC SNR SP
TAC = Type approval code
FAC = Final assembly code
SNR = Serial number
SP = Spare
*#0000# To view Software Version.
#746025625# [*#sim0clock#]
Checks if the sim clock can be stopped. Sim clock stop is a kind of stand-by mode which will save battery time. This code doesn't work with software version 4.59.
*#92702689# [*#war0anty#] takes you to a secret menu with 6 choices:
1. Displays Serial Number.
2. Displays the Month and Year of Manufacture (0997)
3. Displays (if there) the date where the phone was purchased (MMYY)
4. Displays the date of the last repairment - if found (0000)
5. makes you capebel of transferring user data if you have the gear for it
6. shows how many hours the phone has been on
Latest software version: V 5.02 NSE-8/9
*#3370# - Enhanced Full Rate Codec (EFR) activation. It will automatically restart.
*#3370* - Enhanced Full Rate Codec (EFR) deactivation. It will automatically restart.
*#4720# - Half Rate Codec activation. It will automatically restart
*#4720* - Half Rate Codec deactivation. It will automatically restart
Enhanced Full Rate will give you much better sound quality when you enable it. The new Enhanced Full Rate CODEC adopted by GSM uses the ASELP (Algebraic Code Excitation Linear Prediction) compression technology. This technology allows for much great voice quality in the same number of bits as the older Full Rate CODEC. The older technology was called LPC-RPE (Linear Prediction Coding with Regular Pulse Excitation). Both operate at 13 kilobits.(but you take up more space on the network, so they can charge you more) - Talk-time is reduced by about 5% when using the ERF option.
Samsung D series hack
Tips and Tricks for the D820, D900, and other Samsung phones with similar firmware.
#*22671* - Starts the phone recording in the background. It can record up to an hour, secretly. Press #*22672*
Holding the volume button when the screen is off displays a short summary of information. Time, Date, signal, missed calls, etc...
Enter code *#1234# to display Firmware version of the phone
Example : D900XAFG6
D900 = model
XA = Region / Country
F = Year (2006)
G = Month (July)
6 = Firmware Release in month (so this is the 6th revision)
Hold down # to mute, or unmute the phone.
Press 1 while watching a video to make it full screen.
While playing a song in music player u can highlight a part of the song to be repeated over, while listening to the song press 7 at the point u want repeated then press 7 again at the end of the section and it will loop the section between the the two presses of 7
If you need to send a photo via mms and its too big to send and u have no pc available to downsize the pic (my limit is 100kb via mms with my sim) open the photo in photo editor on the phone and "save as" rename it differently from the original and u will have two copys of the pic and the edited version will be under 100kb.
Hidden Menu: *#8999*8378#
Make MP3 sound louder:
1. hit: *#8999*8378#
2. hit: 2, and then 2 again.
3. then on IIS NORMAL (or hit 9)
4. then on "Rx vol."
5. for level 10, click 0
then save
Orignals are:
level 10 = 10
level 9 = 18
Make sound setting louder when som1s calling:
1. *#8999*8378#
2. 2 times 2
3. 1 (NORMAL)
4. then on "Rx vol."
5. level 5 type 140 instead of 120
Samsung Mobile Service Center CODES
*#06# -> Show IMEI
*#9999# -> Show Software Version
*#0837# -> Show Software Version (instructions)
*#0001# -> Show Serial Parameters
*#9125# -> Activates the smiley when charging.
*#9998*228# -> Battery status (capacity, voltage, temperature)
*#9998*246# -> Program status
*#9998*289# -> Change Alarm Buzzer Frequenc
y
*#9998*324# -> Debug screens
*#9998*364# -> Watchdog
*#9998*377# -> EEPROM Error Stack - Use side keys to select values. Cancel and ok.
*#9998*427# -> Trace Watchdog
*#9998*523# -> Change LCD contrast - Only with version G60RL01W
*#9998*544# -> Jig detect
*#9998*636# -> Memory status
*#9998*746# -> SIM File Size
*#9998*778# -> SIM Service Table
*#9998*785# -> RTK (Run Time Kernel) errors - if ok then phn is reset, info is put in memory error. *#9998*786# -> Run, Last UP, Last DOWN
*#9998*837# -> Software Version
*#9998*842# -> Test Vibrator - Flash the screenligth during 10 seconds and vibration activated.
*#9998*862# -> Vocoder Reg - Normal, Earphone or carkit can be selected
*#9998*872# -> Diag
*#9998*947# -> Reset On Fatal Error
*#9998*999# -> Last/Chk
*#9998*9266# -> Yann debug screen (=Debug Screens?)
*#9998*9999# -> Software version
*0001*s*f*t# -> Changes serial parameters (s=?, f=0,1, t=0,1) (incomplete)
*0002*?# -> unknown
*0003*?# -> unknown
SP-unlock SGH-600 and SGH 2100
*2767*3855# -> Full EEPROM Reset ( THIS CODE REMOVES the Security Lock and formats The Mobile's Chipset )
But also changes IMEI to 447967-89-400044-0, To restore your old IMEI use the IMEI program found on the software page.
*2767*2878# -> Custom EEEPROM Reset ( does not change the securitu CODE )
These codes has been tested with version FLD_2C6 G60SB03X of Samsung SGH-600
Samsung Research Center Codes
You can try these in case you downloaded corrupted or incompatible Java midlets or other media, which are causing problems with the phone.
*2767*JAVA# Java Reset and (Deletes all Java Midlets)
*2767*MEDIA# Reset Media (Deletes All Sounds and Pics)
*2767*WAP# Wap Reset
*2767*CUST# Reset Custom EEPR0M
*2767*FULL# Reset Full EEPR0M (Caution)
For example : *2767*JAVA# would be keyed in as *2767*5282#
Note : Not all codes will work with SGH-C100.
Other Samsung Codes
*#06# IMEI code
*#9998*4357# Help Menu
*#9998*5282# Java menu (GRPS/CSD settings for JAVA server)
*#9999#0# Monitor Mode
*#9999# or *#9998*9999# Software Version
*#8888# or *#9998*8888# Hardware Version
*#9998*746# or *#9998*0746# or *#0746# Sim Infos
*#9998*523# or *#9998*0523# or *#0523# Display Contrast
*#9998*842# or *#9998*0842# or *#0842# Vibration On (until you push OK)
*#9998*289# or *#9998*0289# or *#0289# Buzzer On (until you push OK)
*#9998*288# or *#9998*0288# or *#0288# Battery & Field Infos
*#9998*377# or *#9998*0377# Error log
*#9998*778# or *#9998*0778# or *#0778# Sim Service table
*#9998*782# show date and alarm clock
*#8999*638# show network information
*#9998*5646# change operator logo at startup
*#9998*76# production number
*#9998*968# view melody for alarm
*#9998*585# Non-Volatile Memory (NVM)
*#3243948# Digital Audio Interference Off
*#32436837# Digital Audio Interference On
SAMSUNG T100 SECRET CODES
============================
*#06# -> Show IMEI
*#9999# -> Show Software Version
*#0001# -> Show Serial Parameters
*2767*3855# -> Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!!!! but also change IMEI to 447967-89-400044-0, you must use CHGIMEI to restore it)
*2767*2878# -> Custom EEEPROM Reset
*#8999*228# -> Battery status (capacity, voltage, temperature)
*#8999*246# -> Program status
*#8999*289# -> Change Alarm Buzzer Frequency
*#8999*324# -> Debug screens
*#8999*364# -> Watchdog
*#8999*377# -> EEPROM Error Stack
*#8999*427# -> Trace Watchdog
*#8999*523# -> Change LCD contrast
*#8999*544# -> Jig detect
*#8999*636# -> Memory status
*#8999*746# -> SIM File Size
*#8999*778# -> SIM Service Table
*#8999*785# -> RTK (Run Time Kernel) errors
*#8999*786# -> Run, Last UP, Last DOWN
*#8999*837# -> Software Version
*#8999*842# -> Test Vibrator
*#8999*862# -> Vocoder Reg
*#8999*872# -> Diag
*#8999*947# -> Reset On Fatal Error
*#8999*999# -> Last/Chk
*#8999*9266# -> Yann debug screen (=Debug Screens?)
*#8999*9999# -> Software version
SAMSUNG V200 SECRET CODES
v200 Unlock Code-> *2767*7822573738#
*#9324# Netmon (press the hangup key to exit)
*#9998*JAVA# Edit GPRS/ CSD settings (S100 Only)
*#9998*Help# Help screen/ List of codes
*#9998*LOGO# Change operator Logo
*#9998*RTC# RTC Display
*#9998*Bat# Battery Status
*#9998*Buz# Turns Buzzer ON
*#9998*Vib# Turns Vibrator ON
*#9998*LCD# LCD Contrast
*#9998*9999# Softwre Version
*#9998*8888# Hardware Version
*#9998*377# NVM Error Log (?????)
*#9998*NET# SIM Network ID
*#9998*778# SIM Serv. Table
*#9998*SIM# SIM Info
*#9998*PN# Production No.
*#9998*968# Reminder Tune
*#9998*NVM# Displays Non-Volitile Memory Status
*#9999*C# ???????????????????
*#06# Displays phones I**I No.
***/// ***/// NOTE /// *** RED COLOR , they appear serious !!! Use at
own risk !!!
*#9998*2576# Forces SIM Error
*#9998*DEAD# Forces Phone Crash
*2767*MEDIA# Resets the medis on the phone (deletes all downloaded
pics/tones)
*2767*FULL# Resets the EEPRON *DANGEROUS*
*2767*CUST# Resets the Custom EEPRON
*2767*JAVA# Resets JAV downloads (deletes all downloaded midlits)
*2767*STACKRESET# Resets Stack
*2767*225RESET# ????????????????? * Dangerous *
*2767*WAP# Resets WAP Setting & Deletes Favorites
SAMSUNG A800 SECRET CODES
The universal unlock code is *2767*637# do this with out your sim in
By default, the firmware (software) for x600 only receives java
apps and other applications like stuff by serial port.
but even for it, you have to enable the serial port, which also
causes
the closing of all other ports, even the IrDA too :-( ..
well, guess what, i have very good news for you,
do you know, you can increase the sound level,
the sound level for tones, speaker fone, etc,
can be increase even then if it is at max (level 4)
you still can do it,
just follows the instructions!
**************** HERE WE GO **************
Enter the following code:
*#8999*8378#
(You'll be shown menu, then ...)
then go to:
"H/W test"
then go to:
"Audio Settings"
then go to:
"Melody Gain"
There will you see a number.
there are five (5) Melody Levels" of it.
(and currently, you are at level 1 and after
pressing the "save" button, you will move to
level 2 and so on .........................)
you have to change the values of all the levels.
and as the resultant, it will give increase the
melody sound!, your tones will more louder,
even more louder then the max. ringing volume.
the level wise numbers are: (as its my setting :-) )
Melody Level 1: 13
Melody Level 2: 17
Melody Level 3: 18
Melody Level 4: 25
Melody Level 5: 31
you even can make your own combinations of level wise
sounding numbers that can change the sound level!.
if your combination cause more louder sound level,
then mine,
then do share it with the group! ... :-)
meanwhile, try my figured-out combination!
************ CAUTION ************
if anything goes wrong,
then you can apply the master reset code,
that will NOT delete anything, ANYTHING from your
cell fone, but set each and eveything to its
default/standard setting ...
(likes, factory settings :-) )
the master reset code is:
#*7728#
#########################################
I take no responsibility of these codes are working or not,
or its effects on your cell fone
but i have tried these codes on my cell fone.
and i bet, nothing goes wrong,
but even then of my words, be carefull!,
#########################################
The code: *#8999*8378#
as i regarded it a informative code,
will tell you each and everything about your cell fone.
and in the "H/W test",
there are lot of other Audio settings,
each of them having five (5) levels,
you can change the combination, but before doing anything,
do write the defult number sequence to some place so that
you'll be then able to invert it again! .. :-) ...
#*2558# - Time ON
#*2527# - GPRS Switching Set to class {4/8/9/10}
#*4263# - Handsfree Mode: ACTIVATED
#*53696# - [Java dnload] WAPSAR mode
#*536961# - WAPSAR enable HTTP disable
#*536962# - HTTP enable WAPSAR disable
#*536963# - SERIAL enable Others disable
#*5663351# - [Phone Model] SAMSUNG SGH-X100
#*6420# - Mic off
#*6421# - Mic on
#*7632# - Sleep mode
*#8999*523# - Main LCD Brightness
*#8999*3825523# - (?) External display
*2767*3855# - Full EEPROM reset(Reset all type of locks)also you'll
lose pictures and java not melody
Remove camera sound:
On main screen type:
*#8999*8378# --> Test mode
H/W test
Audio Settings
Melody Gain
Then replace 6 by 0, it'll show 12 but it's OK
Press back until main screen
Then press key volume to minimum and let's try !!! no more sound
tip by C-Quest
*2767*688# resets the phone
Thats all!!!!!!!!!!!!!!!
Samsung X100 Tricks
#*0000#
#*0400#
#*1200# - AFC DAC Val
#*1300# - IMEI
#*1400# - IMSI
#*1700# - ( ) Command #*1700 Executed
#*1800# - ( ) Command #*1800 Executed
#*1900# - ( ) Command #*1900 Executed
#*2000# - ( ) Command #*2000 Executed
#*2100# - ( ) Command #*2100 Executed
#*2200# - ( ) Command #*2200 Executed
#*2252# - Current CAL
#*2255# -
#*2256# - Calibr.-Info
#*2282#
#*2285#
#*2286# - Databattery
#*2337# - ( ) Permanent Registration - Not Yet Implemented
#*2355#
#*2400# - ( ) Command #*2400 Executed
#*2474# - For CMD Set - DEBUGBATTERY in cihard.opt
#*2527# - GPRS Switching Set to class {4/8/9/10}
#*2558# - Time ON
#*2562#
#*2565#
#*2677# - AMR State: {None / Full Rate}
#*2679# - Copycat Feature: {ACTIVATED/DEACTIVATED}
#*2787# - CRTP {ON/OFF}
#*2834# - Audio path Mobile Normal
#*2836# - AVDDSS Management: {DEACTIVATED/ACTIVATED}
#*3230# - Trace Enable DCD disable
#*3231# - Trace disable DCD Enable
#*3232# - Current Mode {Trace enabled/DCD enabled}
#*3270# - DCS Support: {DEACTIVATED/ACTIVATED}
#*3282# - Data: {DEACTIVATED/ACTIVATED}
#*3333#
#*3353# - General Defence Code Erased
#*3370#
#*3377#
#*3476# - EGSM: {DEACTIVATED/ACTIVATED}
#*3676# - Flash Volume Formated
#*3683#
#*3737# - Some Codes
#*3777#
#*3779#
#*3825# - ( ) Command #*3825 Executed
#*3837#
#*3849#
#*3851#
#*3876#
#*3877# - Dump of SPY Trace
#*3900#
#*3940# - External looptest 9600 bps not available in SYSOL2
#*3940# - External looptest 115200 bps not available in SYSOL2
#*3941#
#*4200#
#*4263# - Handsfree Mode: ACTIVATED
#*4300#
#*4500#
#*4674# - IMSI| MCC:2 5 0 | MNC 9 2 | 10 11 91 83 50
#*4700# - Half Rate: {ACTIVATED/DEACTIVATED}
#*4760# - GSM: {ACTIVATED/DEACTIVATED}
#*4864#
#*5100#
#*5111# - ( ) Some Codes
#*5132#
#*5133# - ( ) Some Codes
#*5143#
#*5156#
#*5165#
#*5171# - ( ) Some Codes
#*5172# - ( ) Some Codes
#*5173# - ( ) Some Codes
#*5174#
#*5175#
#*5176# - ( ) Some Codes
#*5177#
#*5187# - L1C2G trace: {ACTIVATED/DEACTIVATED}
#*53696# - [Java dnload] WAPSAR mode
#*536961# - WAPSAR enable HTTP disable
#*536962# - HTTP enable WAPSAR disable
#*536963# - SERIAL enable Others disable
#*5376#
#*5400# - ( ) Command #*5400 Executed
#*5500#
#*5600#
#*566335# - [WAP model ID]
#*5663351# - [Phone Model] SAMSUNG SGH-X100
#*5663352# - [Java Model] SEC-SGHS300/1.0
#*5737425# - Java Serial
#*577699# - APN
#*5800# - ( ) Command #*5800 Executed
#*6100# - ( ) Command #*6100 Executed
#*6200#
#*6420# - Mic off
#*6421# - Mic on
#*6422# - Mic dep RXdata
#*6428# - Mic measurement
#*6700#
#*6837# - Official Software Version
#*6900#
#*7200#
#*7222# - Operation Typ: Class C GSM
#*7224# - ERROR
#*7247#
#*7252# - Operation Typ: Class B GPRS
#*7271# - Multi slot: Class 1 GPRS
#*7274# - Multi slot: Class 4 GPRS
#*7276#
#*7284# - Class B
#*7287# - GPRS Attached
#*7288# - GPRS Detached
#*7326# - Accessory: Vibrator
#*7337# - Some kind of Reset Settings
#*7352# - Some Kind of Debug Info
#*7462# - SIM phase
#*7524# - KCGPRS
#*7562# - LOCI GPRS
#*7636#
#*7639#
#*7632# - Sleep mode
#*7633#
#*7638# - RLC always open ended TBF: {ACTIVATED/DEACTIVATED}
#*7646#
#*7665#
#*7666# - SrCell Data
#*7673# - Sleep mode
#*7676# - Command #*7676 Executed
#*7683# - Sleep variable
#*7693# - Sleep deact
#*7728# - RSAV done->reset
#*7763# - SMS bearer CS {ACTIVATED/DEACTIVATED}
#*7825#
#*7828# - Midl Rl51
#*7957# - Command #*7957 Executed
#*7983# - Voltage/Freq {DEACTIVATED/ACTIVATED}
#*7986# - Voltage {DEACTIVATED/ACTIVATED}
#*8462# - Sleep time since SwitchOff
#*8465# - Time in L1
#*8466# - Old Time
#*8645#
#*9278# - Command #*9278 Executed
#*9795# - wtls key: reset
#7263867# - RAM Dump {On/Off}
#7465625*228# - Activa lock deactivated
#7465625*27*
#7465625*2827# - Auto CP lock deactivated
#7465625*28638# - Auto Network lock deactivated
#7465625*28746# - Auto SIM lock deactivated
#7465625*2877# - Auto SP lock deactivated
#7465625*28782# - Auto subset lock deactivated
#7465625*638*
#7465625*746*
#7465625*77*
#7465625*782*
#8999*324#
*#0*
*#0020# –
*#06# – IMEI
*#2255# - Call List
*#4777*8665# – GPRS
*#7465625# – Interrogate ( )
*#8377466# – Software && Hardware Versions
*#8888# – Hardware Version
*#8999*324# - ( ) Some Strange Numbers
*#8999*377# -
*#8999*3825523# - ( )
*#8999*523# - Main LCD Brightness
*#8999*636# - ( ) Another Strange Numbers
*#8999*8376363# - . HW, SW, + Some Code And Data
*#8999*8378# - . , , , HW SW
*#9999# – Software Version
=== : ===
*2767*xx927 - WAP . xx - . , xx=44: *2767*44WAP# xx=31: *2767*31WAP#
*2767*xx667 - MMS.
.
*2767*2877368#
*2767*2878# – EEPROM ( , )
*2767*31667#
*2767*31927#
*2767*33667#
*2767*33927#
*2767*34667#
*2767*34927#
*2767*351667#
*2767*351927#
*2767*3700#
*2767*380667#
*2767*380927#
*2767*3855# - l EEPROM ( SP- !! ) IMEI 447967-89-400044-0, IMEI ( )
*2767*39667#
*2767*39927#
*2767*420667#
*2767*420927#
*2767*43667#
*2767*43927#
*2767*44667#
*2767*44927#
*2767*46667#
*2767*46927#
*2767*49667#
*2767*49927#
*2767*66335#
*2767*688# ( ) [Unlocking Code]
*2767*7100#
*2767*7300#
*2767*73738927# = *2767*RESETWAP#
*2767*7650#
*2767*7667#
*2767*7927#
*2767*8200#
*2767*927#
=== / : ===
*335#
*663867# - mm file dumped
*7465625# -
*7465625*228# - Activa lock personalized
*7465625*27*
*7465625*2827# - Auto CP lock activated
*7465625*28638# - Auto Network lock activated
*7465625*28746# - Auto SIM lock activated
*7465625*2877# - Auto SP lock activated
*7465625*28782# - Auto subset lock activated
*7465625*638*
*7465625*746
*7465625*746*
*7465625*77*
*7465625*782*
Secret Codes
*#06# -> Show IMEI
*#9999# -> Show Software Version
*#0837# -> Show Software Version (instructions)
*#0001# -> Show Serial Parameters
*#9125# -> Activates the smiley when charging.
*#9998*228# -> Battery status (capacity, voltage, temperature)
*#9998*246# -> Program status
*#9998*289# -> Change Alarm Buzzer Frequency
*#9998*324# -> Debug screens
*#9998*364# -> Watchdog
*#9998*377# -> EEPROM Error Stack - Use side keys to select values. Cancel and ok.
*#9998*427# -> Trace Watchdog
*#9998*523# -> Change LCD contrast - Only with version G60RL01W
*#9998*544# -> Jig detect
*#9998*636# -> Memory status
*#9998*746# -> SIM File Size
*#9998*778# -> SIM Service Table
*#9998*785# -> RTK (Run Time Kernel) errors - if ok then phn is reset, info is put in memory error. *#9998*786# -> Run, Last UP, Last DOWN
*#9998*837# -> Software Version
*#9998*842# -> Test Vibrator - Flash the screenligth during 10 seconds and vibration activated.
*#9998*862# -> Vocoder Reg - Normal, Earphone or carkit can be selected
*#9998*872# -> Diag
*#9998*947# -> Reset On Fatal Error
*#9998*999# -> Last/Chk
*#9998*9266# -> Yann debug screen (=Debug Screens?)
*#9998*9999# -> Software version
*0001*s*f*t# -> Changes serial parameters (s=?, f=0,1, t=0,1) (incomplete)
*0002*?# -> unknown
*0003*?# -> unknown
SP-unlock SGH-600 and SGH 2100
*2767*3855# -> Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!! )
But also changes IMEI to 447967-89-400044-0, To restore your old IMEI use the IMEI program found on the software page.
*2767*2878# -> Custom EEEPROM Reset
These codes has been tested with version FLD_2C6 G60SB03X of Samsung SGH-600
SAMSUNG SECRET CODES (NEW)
Latest
*#1111# S/W Version
*#1234# Firmware Version
*#2222# H/W Version
*#8999*8376263# All Versions Together
*#8999*8378# Test Menu
*#4777*8665# GPSR Tool
*#8999*523# LCD Brightness
*#8999*377# Error Menu
*#8999*327# EEP Menu
*#8999*3825523# Don't Know.
*#8999*667# Debug Mode
*#92782# PhoneModel (Wap)
#*5737425# JAVA Mode
*#2255# Call List
*#232337# Bluetooth MAC Adress
*#5282837# Java Version
#*4773# Incremental Redundancy
#*7752# 8 PSK uplink capability bit
#*7785# Reset wakeup & RTK timer cariables/variables
#*1200# ????
#*7200# Tone Generator Mute
#*3888# BLUETOOTH Test mode
#*#8999*324# ??
#*7828# Task screen
#*5111# ??
#*#8377466# S/W Version & H/W Version
#*2562# Restarts Phone
#*2565# No Blocking? General Defense.
#*3353# General Defense, Code Erased.
#*3837# Phone Hangs on White screen
#*3849# Restarts Phone
#*3851# Restarts Phone
#*3876# Restarts Phone
#*7222# Operation Typ: (Class C GSM)
#*7224# !!! ERROR !!!
#*7252# Operation Typ: (Class B GPRS)
#*7271# CMD: (Not Available)
#*7274# CMD: (Not Available)
#*7337# Restarts Phone (Resets Wap Settings)
#*2787# CRTP ON/OFF
#*2886# AutoAnswer ON/OFF
#*3737# L1 AFC
#*5133# L1 HO Data
#*7288# GPRS Detached/Attached
#*7287# GPRS Attached
#*7666# White Screen
#*7693# Sleep Deactivate/Activate
#*7284# L1 HO Data
#*2256# Calibration info? (For CMD set DEBUGAUTONOMY in cihard.opt)
#*2286# Databattery
#*2527# GPRS switching set to (Class 4, 8, 9, 10)
#*2679# Copycat feature Activa/Deactivate
#*3940# External looptest 9600 bps
#*4263# Handsfree mode Activate/Deactivate
#*4700# Please use function 2637
#*7352# BVMC Reg value (LOW_SWTOFF, NOMINAL_SWTOFF)
#*2558# Time ON
#*3370# Same as 4700
#*3941# External looptest 115200 bps
#*5176# L1 Sleep
#*7462# SIM Phase
#*7983# Voltage/Freq
#*7986# Voltage
#*8466# Old Time
#*2255# Call Failed
#*5187# L1C2G trace Activate/Deactivate
#*5376# DELETE ALL SMS!!!!
#*6837# Official Software Version: (0003000016000702)
#*7524# KCGPRS: (FF FF FF FF FF FF FF FF 07)
#*7562# LOCI GPRS: (FF FF FF FF FF FF FF FF FF FF FF FE FF 01)
#*2337# Permanent Registration Beep
#*2474# Charging Duration
#*2834# Audio Path (Handsfree)
#*3270# DCS Support Activate/Deactivate
#*3282# Data Activate/Deactivate
#*3476# EGSM Activate/Deactivate
#*3676# FORMAT FLASH VOLUME!!!
#*4760# GSM Activate/Deactivate
#*4864# White Screen
#*5171# L1P1
#*5172# L1P2
#*5173# L1P3
#*7326# Accessory
#*7683# Sleep variable
#*8465# Time in L1
#*2252# Current CAL
#*2836# AVDDSS Management Activate/Deactivate
#*3877# Dump of SPY trace
#*7728# RSAV
#*2677# Same as 4700
#*3797# Blinks 3D030300 in RED
#*3728# Time 2 Decod
#*3725# B4 last off
#*7372# Resetting the time to DPB variables
#*7732# Packet flow context bit Activate/Deactivate
#*6833# New uplink establishment Activate/Deactivate
#*3273# EGPRS multislot (Class 4, 8, 9, 10)
#*7722# RLC bitmap compression Activate/Deactivate
#*2351# Blinks 1347E201 in RED
#*4472# Hysteresis of serving cell: 3 dB
#*2775# Switch to 2 inner speaker
#*9270# Force WBS
#*7878# FirstStartup (0=NO, 1=YES)
#*3757# DSL UART speed set to (LOW, HIGH)
#*8726# Switches USBACM to Normal
#*8724# Switches USBACM to Generator mode
#*8727# Switches USBACM to Slink mode
#*8725# Switches USBACM to Loop-back mode
#*3838# Blinks 3D030300 in RED
#*2077# GPRS Switch
#*2027# GPRS Switch
#*0227# GPRS Switch
#*0277# GPRS Switch
#*22671# AMR REC START
#*22672# Stop AMR REC (File name: /a/multimedia/sounds/voice list/ENGMODE.amr)
#*22673# Pause REC
#*22674# Resume REC
#*22675# AMR Playback
#*22676# AMR Stop Play
#*22677# Pause Play
#*22678# Resume Play
#*77261# PCM Rec Req
#*77262# Stop PCM Rec
#*77263# PCM Playback
#*77264# PCM Stop Play
#*2872# CNT
*#8999*283# ???
#*22679# AMR Get Time
*288666# ???
*2886633# ???
*#8999*364# Watchdog ON/OFF
#*8370# Tfs4.0 Test 0
#*8371# Tfs4.0 Test 1
#*8372# Tfs4.0 Test 2
#*8373# Tfs4.0 Test 3
#*8374# Tfs4.0 Test 4
#*8375# Tfs4.0 Test 5
#*8376# Tfs4.0 Test 6
#*8377# Tfs4.0 Test 7
#*8378# Tfs4.0 Test 8
#*8379# Tfs4.0 Test 9
#837837# error=...
#*36245# Turns Email TestMenu on.
*2767*22236245# Email EPP set (....)!
*2767*837836245# Email Test Account!
*2767*29536245# Email Test2 Account!
*2767*036245# Email EPP reset!
*2767*136245# Email EPP set (1)!
*2767*736245# Email EPP set (7)!
*2767*3036245# Email...
*2767*3136245# Email...
*2767*3336245# Email...
*2767*3436245# Email...
*2767*3936245# Email...
*2767*4136245# Email...
*2767*4336245# Email...
*2767*4436245# Email...
*2767*4536245# Email...
*2767*4636245# Email...
*2767*4936245# Email...
*2767*6036245# Email...
*2767*6136245# Email...
*2767*6236245# Email...
*2767*6336245# Email...
*2767*6536245# Email...
*2767*6636245# Email...
*2767*8636245# Email...
*2767*85236245# Email...
*2767*3855# = E2P Full Reset
*2767*2878# = E2P Custom Reset
*2767*927# = E2P Wap Reset
*2767*226372# = E2P Camera Reset
*2767*688# Reset Mobile TV
#7263867# = RAM Dump (On or Off)
*2767*49927# = Germany WAP Settings
*2767*44927# = UK WAP Settings
*2767*31927# = Netherlands WAP Settings
*2767*420927# = Czech WAP Settings
*2767*43927# = Austria WAP Settings
*2767*39927# = Italy WAP Settings
*2767*33927# = France WAP Settings
*2767*351927# = Portugal WAP Settings
*2767*34927# = Spain WAP Settings
*2767*46927# = Sweden WAP Settings
*2767*380927# = Ukraine WAP Settings
*2767*7927# = Russia WAP Settings
*2767*30927# = GREECE WAP Settings
*2767*73738927# = WAP Settings Reset
*2767*49667# = Germany MMS Settings
*2767*44667# = UK MMS Settings
*2767*31667# = Netherlands MMS Settings
*2767*420667# = Czech MMS Settings
*2767*43667# = Austria MMS Settings
*2767*39667# = Italy MMS Settings
*2767*33667# = France MMS Settings
*2767*351667# = Portugal MMS Settings
*2767*34667# = Spain MMS Settings
*2767*46667# = Sweden MMS Settings
*2767*380667# = Ukraine MMS Settings
*2767*7667#. = Russia MMS Settings
*2767*30667# = GREECE MMS Settings
*#7465625# = Check the locks
*7465625*638*Code# = Enables Network lock
#7465625*638*Code# = Disables Network lock
*7465625*782*Code# = Enables Subset lock
#7465625*782*Code# = Disables Subset lock
*7465625*77*Code# = Enables SP lock
#7465625*77*Code# = Disables SP lock
*7465625*27*Code# = Enables CP lock
#7465625*27*Code# = Disables CP lock
*7465625*746*Code# = Enables SIM lock
#7465625*746*Code# = Disables SIM lock
*7465625*228# = Activa lock ON
#7465625*228# = Activa lock OFF
*7465625*28638# = Auto Network lock ON
#7465625*28638# = Auto Network lock OFF
*7465625*28782# = Auto subset lock ON
#7465625*28782# = Auto subset lock OFF
*7465625*2877# = Auto SP lock ON
#7465625*2877# = Auto SP lock OFF
*7465625*2827# = Auto CP lock ON
#7465625*2827# = Auto CP lock OFF
*7465625*28746# = Auto SIM lock ON
#7465625*28746# = Auto SIM lock OFF
**********************
#*7878# FirstStartup (0=NO, 1=YES)
#*3838# Blinks 3D030300 in RED
#*2077# GPRS Switch
#*2027# GPRS Switch
#*0227# GPRS Switch
#*0277# GPRS Switch
#*22671# AMR REC START
#*22672# Stop AMR REC (File name: /a/multimedia/sounds/voice list/ENGMODE.amr)
#*22673# Pause REC
#*22674# Resume REC
#*22675# AMR Playback
#*22676# AMR Stop Play
#*22677# Pause Play
#*22678# Resume Play
#*77261# PCM Rec Req
#*77262# Stop PCM Rec
#*77263# PCM Playback
#*77264# PCM Stop Play
#*22679# AMR Get Time
*#8999*364# Watchdog ON/OFF
*#8999*427# WATCHDOG signal route setup
*2767*3855# = Full Reset (Caution every stored data will be deleted.)
*2767*2878# = Custom Reset
*2767*927# = Wap Reset
*2767*226372# = Camera Reset (deletes photos)
*2767*688# Reset Mobile TV
#7263867# = RAM Dump (On or Off)
Samsung Secret Codes Part 3
*2767*49927# = Germany WAP Settings
*2767*44927# = UK WAP Settings
*2767*31927# = Netherlands WAP Settings
*2767*420927# = Czech WAP Settings
*2767*43927# = Austria WAP Settings
*2767*39927# = Italy WAP Settings
*2767*33927# = France WAP Settings
*2767*351927# = Portugal WAP Settings
*2767*34927# = Spain WAP Settings
*2767*46927# = Sweden WAP Settings
*2767*380927# = Ukraine WAP Settings
*2767*7927# = Russia WAP Settings
*2767*30927# = GREECE WAP Settings
*2767*73738927# = WAP Settings Reset
*2767*49667# = Germany MMS Settings
*2767*44667# = UK MMS Settings
*2767*31667# = Netherlands MMS Settings
*2767*420667# = Czech MMS Settings
*2767*43667# = Austria MMS Settings
*2767*39667# = Italy MMS Settings
*2767*33667# = France MMS Settings
*2767*351667# = Portugal MMS Settings
*2767*34667# = Spain MMS Settings
*2767*46667# = Sweden MMS Settings
*2767*380667# = Ukraine MMS Settings
*2767*7667#. = Russia MMS Settings
*2767*30667# = GREECE MMS Settings
*#7465625# = Check the phone lock status
*7465625*638*Code# = Enables Network lock
#7465625*638*Code# = Disables Network lock
*7465625*782*Code# = Enables Subset lock
#7465625*782*Code# = Disables Subset lock
*7465625*77*Code# = Enables SP lock
#7465625*77*Code# = Disables SP lock
*7465625*27*Code# = Enables CP lock
#7465625*27*Code# = Disables CP lock
*7465625*746*Code# = Enables SIM lock
#7465625*746*Code# = Disables SIM lock
*7465625*228# = Activa lock ON
#7465625*228# = Activa lock OFF
*7465625*28638# = Auto Network lock ON
#7465625*28638# = Auto Network lock OFF
*7465625*28782# = Auto subset lock ON
#7465625*28782# = Auto subset lock OFF
*7465625*2877# = Auto SP lock ON
#7465625*2877# = Auto SP lock OFF
*7465625*2827# = Auto CP lock ON
#7465625*2827# = Auto CP lock OFF
*7465625*28746# = Auto SIM lock ON
#7465625*28746# = Auto SIM lock OFF
Type *#9998*627837793# Go to the 'my parameters' and there you will find new menu where you can unlock phone.(not tested-for samsung C100)
To unlock a Samsung turn the phone off take the sim card and type the following code *#pw+15853649247w# .
Java status code: #*53696# (Samsung X600)
If you want to unlock your phone put a sim from another company then type *#9998*3323# it will reset your phone. Push exit and then push 7, it will reset again. Put your other sim in and it will say sim lock, type in 00000000 then it should be unlocked. Type in *0141# then the green call batton and it's unlocked to all networks. This code may not work on the older phones and some of the newer phones. If it doesn't work you will have to reset your phone without a sim in it by typing *#2767*2878# or *#9998*3855# (not tested)
*2767*688# = Unlocking Code
*#8999*8378# = All in one Code
*#4777*8665# = GPSR Tool
*#8999*523# = LCD Brightness
*#8999*3825523# = External Display
*#8999*377# = Errors
#*5737425# = JAVA Something{I choose 2 and it chrashed}][/b]
*#2255# = Call List
#*536961# = Java Status Code
#*536962# = Java Status Code
#*536963# = Java Status Code
#*53696# = Java Status Code
#*1200# = AFC DAC Val
#*1300# = IMEI
#*1400# = IMSI
#*2562# = ??? White for 15 secs than restarts.
#*2565# = Check Blocking
#*3353# = Check Code
#*3837# = ??? White for 15 secs than restarts.
#*3849# = ??? White for 15 secs than restarts.
#*3851# = ??? White for 15 secs than restarts.
#*3876# = ??? White for 15 secs than restarts.
#*7222# = Operation Typ (Class C GSM)
#*7224# = I Got !! ERROR !!
#*7252# = Oparation Typ (Class B GPRS)
#*7271# = Multi Slot (Class 1 GPRS)
#*7274# = Multi Slot (Class 4 GPRS)
#*7276# = Dunno
#*7337# = EEPROM Reset (Unlock and Resets WAP Settings)
#*2787# = CRTP ON/OFF
#*3737# = L1 Dbg data
#*5133# = L1 Dbg data
#*7288# = GPRS Attached
#*7287# = GPRS Detached
#*7666# = SrCell Data
#*7693# = Sleep Act/DeAct (Enable or Disable the Black screen after doing nothing for a while)
#*7284# = Class : B,C or GPRS
#*2256# = Calibration Info
#*2286# = Battery Data
#*2527# = GPRS Switching (set to: class 4, class 8, class 9 or class 10)
#*2679# = Copycat feature (Activate or Deactivate)
#*3940# = External loop test 9600 bps
#*4263# = Handsfree mode (Activate or Deactivate)
#*4700# = Half Rate (Activate or Deactivate)
#*7352# = BVMC Reg value
#*8462# = Sleeptime
#*2558# = Time ON
#*3370# = EFR (Activate or Deactivate)
#*3941# = External looptest 115200 bps
#*5176# = L1 Sleep
#*7462# = SIM phase
#*7983# = Voltage/Frequenci (Activate or Deactivate)
#*7986# = Voltage (Activate or Deactivate)
#*8466# = Old time
#*2255# = Call ???
#*5187# = L1C2G trace (Activate or Deactivate)
#*5376# = ??? White for 15 secs than restarts.
#*6837# = Official Software Version
#*7524# = KCGPRS
#*7562# = LOCI GPRS
#*7638# = RLC allways open ended TBF (Activate or Deactivate)
#*7632# = Sleep mode Debug
#*7673# = Sleep mode RESET
#*2337# = Permanent Registration Beep
#*2474# = ???
#*2834# = Audio Path
#*3270# = DCS support (Activate or Deactivate)
#*3282# = Data (Activate or Deactivate)
#*3476# = EGSM (Activate or Deactivate)
#*3676# = Flash volume formated
#*4760# = GSM (Activate or Deactivate)
#*4864# = Dunno doesn't work on newer versions
#*5171# = L1P1
#*5172# = L1P2
#*5173# = L1P3
#*7326# = Accessory (I got Vibrator)
#*7683# = Sleep variable (
#*7762# = SMS Brearer CS (Activate or Deactivate)
#*8465# = Time in L1
#*9795# = wtls key
#*2252# = Current CAL
#*2836# = AVDDSS Management (Activate or Deactivate)
#*3877# = Dump of SPY trace
#*7728# = RSAV done# (Everything went to standart but nothing was deleted)
#*2677# = ARM State (None or Full Rate)
*#8999*636# = Have no clue what it is, i see 20 lines
*#9999# = Software version
*#8999*8376263# = HW ver, SW ver and Build Date
*#8888# = HW version
*#8377466# = Same HW/SW version thing
*#7465625# = Check the locks
*7465625*638*Code# = Enables Network lock
#7465625*638*Code# = Disables Network lock
*7465625*782*Code# = Enables Subset lock
#7465625*782*Code# = Disables Subset lock
*7465625*77*Code# = Enables SP lock
#7465625*77*Code# = Disables SP lock
*7465625*27*Code# = Enables CP lock
#7465625*638*Code# = Disables Network lock
*7465625*782*Code# = Enables Subset lock
#7465625*782*Code# = Disables Subset lock
*7465625*77*Code# = Enables SP lock
#7465625*77*Code# = Disables SP lock
*7465625*27*Code# = Enables CP lock
#7465625*27*Code# = Disables CP lock
*7465625*746*Code# = Enables SIM lock
#7465625*746*Code# = Disables SIM lock
*7465625*228# = Activa lock ON
#7465625*228# = Activa lock OFF
*7465625*28638# = Auto Network lock ON
#7465625*28638# = Auto Network lock OFF
*7465625*28782# = Auto subset lock ON
#7465625*28782# = Auto subset lock OFF
*7465625*2877# = Auto SP lock ON
#7465625*2877# = Auto SP lock OFF
*7465625*2827# = Auto CP lock ON
#7465625*2827# = Auto CP lock OFF
*7465625*28746# = Auto SIM lock ON
#7465625*28746# = Auto SIM lock OFF
*2767*3855# = E2P Full Reset
*2767*2878# = E2P Custom Reset
*2767*927# = E2P WAP Reset
*2767*226372# = E2P Camera Reset
#*6420# = MIC Off
#*6421# = MIC On
#*6422# = MIC Data
#*6428# = MIC Measurement
#*3230# = Trace enable and DCD disable
#*3231# = Trace disable and DCD enable
#*3232# = Current Mode
#7263867# = RAM Dump (On or Off)
*2767*49927# = Germany WAP Settings
*2767*44927# = UK WAP Settings
*2767*31927# = Netherlands WAP Settings
*2767*420927# = Czech WAP Settings
*2767*43927# = Austria WAP Settings
*2767*39927# = Italy WAP Settings
*2767*33927# = France WAP Settings
*2767*351927# = Portugal WAP Settings
*2767*34927# = Spain WAP Settings
*2767*46927# = Sweden WAP Settings
*2767*380927# = Ukraine WAP Settings
*2767*7927# = Russia WAP Settings
*2767*30927# = GREECE WAP Settings
*2767*73738927# = WAP Settings Reset
*2767*49667# = Germany MMS Settings
*2767*44667# = UK MMS Settings
*2767*31667# = Netherlands MMS Settings
*2767*420667# = Czech MMS Settings
*2767*43667# = Austria MMS Settings
*2767*39667# = Italy MMS Settings
*2767*33667# = France MMS Settings
*2767*351667# = Portugal MMS Settings
*2767*34667# = Spain MMS Settings
*2767*46667# = Sweden MMS Settings
*2767*380667# = Ukraine MMS Settings
*2767*7667#. = Russia MMS Settings
*2767*30667# = GREECE MMS Settings
*335# = Delete all MMS Messages
*663867# = Dump Mm file
#*536961# = WAPSAR enable / HTTP disable
#*536962# = WAPSAR disable / HTTP enable
#*536963# = Serial eable / Others disable
#*53696# = Java Download Mode
#*5663351# = WAP Model ID [Your Model]
#*5663352# = WAP Model ID [SEC-SGHXXXX/1.0]
#*566335# = WAP Model ID [SEC-SGHXXXX/1.0]
*2767*66335# = Check on which model it is
*2767*7100# = SEC-SGHS100/1.0
*2767*8200# = SEC-SGHV200/1.0
*2767*7300# = SEC-SGHS300/1.0
*2767*7650# = Nokia7650/1.0
*2767*2877368# = Reset WAP Model ID to standard.
Sony Ericsson Secret codes
Sony Ericsson Secret Menu: -> * <- <- * <- *
(-> means press joystick, arrow keys or jogdial to the right and <- means left.)
You'll see phone model, software info, IMEI, configuration info, sim lock status, REAL time clock, total call time and text labels.
You can also test your phones services and hardware from this menu (main display, camera, LED/illumination, Flash LED, keyboard, earphone, speaker, microphone, radio and vibrator tests)
IMEI Number: *#06#
Lockstatus: <- * * <-
Shortcut to last dialed numbers: 0#
Shortcut to sim numbers: On main menu type a number and press #
If you change the language from default to any other language, then it may be difficult to switch to default language. The shortcut is very simple. Just press < 0000 > . < stands for left arrow button or joystick and > stands for right arrow button or joystick.
Symbians S60 MOBILES
There is Nothing Remaining Now
Go ahead Explore ur N series : Shankha(Fainted brain)
All Compiled for You
This article is Dedicated to my awesome Friend Akshay ahuja For His Marvelous trust in me and Nokia N72 Phone.. an inspiration to find dis article
Taken From the Symbian Service Center Confidential Manual
05/ dec / 2006
1 : Do u know how to use the edit button (abc or pencil button)?Heres how... in the inbox for example; u wanna delete multiple sms, simply hold the edit button, scroll down, and then, press c to delete the marked sms. The edit button can also b used to copy and past text in sms, simply hold it and scroll across, choose copy. pretty good for placing song names in ngages
Tip 2 : Shit happens, on a smartphone, its inevitable u do something wrong, and tis calls for a format of fone. to format the fone, press *#7370#, then enter the lock code, which is the sec code of the fone. NOTE: batt must b full, else if format is disrupted by low batt, consequences will b disatrous I heard the code *#7780# works too, pretty much the same i tink.for 6600 users, to format the fone, theres an alternative way. Press and hold <3>, <*> and Call (Send) buttons, then power on fone, keep holding on the 3 buttons, till u come to a format screen. this method ONLY works on 6600, and need not enter the sec code. BUT sec code would be reset to default 12345.
Tip 3 : TO NGAGE USERS; Did u know u can install .sis files simply using the cable given? Juz plug it in, place the .sis file anywhere on e: (the mmc), not in any folders, root of e:, disconnect, then look for it in manager.
Tip 4: Save on battery and system memory being used by regulary checking the task manager which can be accessed by holding down the menu button!!
Tip 5: Type *#06# to display your IMEI serial number, very valuable for the unlocking your phone to other sim cards
Tip 6: Type *#0000# to view which firmware version you are running
Tip 4a: Set the screen saver to a short time out period to prolong battery life.Tip 4b: Avoid restarting the phone, or repeatedly turning it on and off. This helps increase battery life.
Tip 7: If you would like to avoid being "blue jacked", keep bluetooth turned off, or set your phone's visibility to hidden.
Tip 8: Don't want to carry a watch and a phone? Set the screen saver to show date and time, then you can ditch the watch.
Tip 9: Save memory when installing apps, by installing over bluetooth. This can be done using the nokia phone suite and a bluetooth serial connection. Only works with .SIS files, so java still has to be sent to the phone, but will save space when using .SIS files
.
Tip 10: Operator logosUse a filemanager like FExplorer or SeleQ to add the folders: "c:/system/Apps/phone/oplogo". Add a .bmp picture to folder "oplogo" and restart your phone! The .bmp picture size needs to be: 97 x 25 pixels
Tip 11: Check if the recepients phone is onDelivery reports
or
Type *0# your message in the message composer window space then write your message, the recipient will not see the star zero hash bit - just the message When they read it it will relay a message back to your fone showing the time they recieved it. (haven't yet tried it myself though)
Tip 12: BlueJacking
First up, you need to know what Bluetooth is. There are lots of types of modern devices that incorporate Bluetooth as one of their many features. PDAs, mobile phones and laptops are a few of these modern devices. Bluetooth means that Bluetooth enabled devices can send things like phonebook/address book contacts, pictures & notes to other Bluetooth enabled devices wirelessly over a range of about 10 metres. So, we've got past the boring part. Now, using a phone with Bluetooth, you can create a phonebook contact and write a message, eg. 'Hello, you've been bluejacked', in the 'Name' field. Then you can search for other phones with Bluetooth and send that phonebook contact to them. On their phone, a message will popup saying "'Hello, you've been bluejacked' has just been received by Bluetooth" or something along those lines. For most 'victims' they will have no idea as to how the message appeared on their phone.
Tip 13: While you are viewing a picture in your phone's gallery, press one of these shortcut keys (definitely works on 6600, not sure about other symbians)1 - turn image anticlockwise3 - turn image clockwise* - toggle on/off of full screen5 - zoom in0 - zoom out
Tip 14 : You can select all files in a folder by selecting THE folder and copy it then paste it somewhere. however u need to make a new directory. fexplorer wun let u copy that folder together. well seleQ can mark files to copy but it really takes time!
Tip 15 :: A soft and Hard resetA Soft-reset - the process of resetting all the settings of the phone to the factory default! No applications are deleted! A Hard-reset is like formatting a drive! It does format the memory. Everything that has been installed after the first use of the phone is deleted! It will recover the memory of the phone to the state you purchased it! It is done by inputing the following code: *#7370# NOTE: The battery must be full or the charger has to be connected to the phone so that it does not run out of power and make the phone unusable.
Tip 16: Formats of images
supported ones: JPG UPF GIF87a/89a WBMB MBM TIFF/F PNG EXIF
How to copy & paste text in your Nokia 3650:Press and hold the pencil key and select your text using the scroll key.Left function key will change to 'Copy'. Press it to copy the selected text to clipboard.You can paste the clipboard contents the same way:press and hold the pencil key and press 'Paste'. Or, press pencil key once and select 'Paste'.
Press and hold the Menu key to open the application switching window, where you can *duh* switch between applications.If a program hangs and you can't shut it down, select the application in theapplication switching window and press 'C' to kill it. It's also a faster way to exit programs.
Turn on/off the "click" sound made by the camera by selecting the 'Silent' profile or by turning warning tones on/off:Menu > Profiles > "select your activated profile" > Personalise > Warning tones > On/Off.(This also effects the sound of Java games and apps).
To change background image go to:Menu > Tools > Settings > Phone > Standby mode > Background image > Yes > "choose an image".The best size for background images is 174x132 pixels.
Only got blue, green and purple in your 3650 colour palette?This free app adds 3 more colours: Palette Extender.
Display an image when someone's calling:Menu > Contacts > "select a contact card" > Options > Edit > Options > Add thumbnail > "choose an image".
Add a personal ringing tone to a contact:Menu > Contacts > "select a contact card" > Options > Open > Options > Ringing tone > "choose a ringing tone".
Delete all messages from your Inbox at once:Menu > Messaging > Inbox > Options > Mark/Unmark > Mark all > Options > Delete.
Send or hide your caller ID: Go to: Menu > Tools > Settings > Call > Send MyCaller ID > 'Yes', 'No' or 'Set By Network' to follow the default settings of your home network.
If you often copy large files to your MultiMedia Card, I recommend a card reader.E.g. With a card reader it takes only 12 seconds to copy a 10 MB file!
Record the sound of a phone call using the (sound) Recorder.Menu > Extra's > Recorder > Options > Record sound clip.Note: short beeps are audible during call registration.But there is a 60 second limitation so if you want unlimited sound recording get this app: Extended Recorder.
While writing text, press "#" to switch between upper and lower case and Dictonary on/off (predictive text input).Press and hold "#" to switch between Alpha mode and Number mode.
Keyboard shortcuts for zooming and rotating images in Images:1 = zoom in, 0 = zoom out, press and hold to return to the normal view.2 = rotate anticlockwise, 9 = rotate clockwise, * = full screen.
In standby mode, press and hold the right soft key to activate voice dialling.To add a voice tag to a phone number, open a contact card and scroll to the phone number and select:Options > Add voice tag.
You can customize both soft keys located below the screen (in standby mode):Menu > Tools > Settings > Phone > Standby mode > Left/Right selection key > "select an application".
In standby mode. press scroll key center (joystick) to go directly to Contacts.
In standby mode, press and hold 0 to launch your wap home page.
In Menu or any subfolder, press numbers 1 - 9 to start the application at that location.123456789
In standby mode,45# + dials the number on your sim in memory slot 45.50# + dials slot 50 and so on.
If you have your keylock activated just press the on/off button to turn on your backlightto look at the time when it's dark without having to unlock the keypad.
Never, ever, in your whole life, install WildSkinz on your Nokia 3650!!! WildSkinz screws upthe whole 3650 system. It was never intended to work on the 3650, only on the 7650.
Why assigning Video Recorder in the right or left soft key does not work?
(Sound Recorder is launched instead of Video Recorder)It's a bug with firmware version 2.50.
How to check your firmware version:
A "Firmware" is the phone's operating system stored in internal Flash memory of the device (disk Z.Manufacturers release new firmware versions containing bug fixes, improvements and - sometimes - offering new functions.Firmware upgrade can only be made in authorized Nokia service centre (point).To check your current firmware version simply type *#0000# on main Phone screen.
?
How to check your IMEI (International Mobile Equipment Identity)?
Type *#06# on main Phone screen.
Start up in Safe Mode so no 'auto start' apps will be running:
To make sure that no memory-resident programs start when you reboot your phone,hold down the pencil key when you turn on the phone and hold it on untill you have to enter your PIN code.(When you have trouble booting up the phone with the MMC in it because it got corrupted for some reason, this trick willalmost always let you boot up the phone so you can remove the latest installed app which might have caused theproblem or if your phone is "unrepairable" you can still back up your important data before you do a format.)
Q: How to totally format your Nokia 3650 and remove all installed applications, user files and restore allsettings to default like it's new out of the box? (OEM apps won't be deleted like Camera and RealOne Player).
A: First Format your MMC: Menu > Extras > Memory > Options > Format mem. card > Yes.Note: It is very important to format your MMC before you format your phone!Then format your phone by typing *#7370# on main Phone screen.Phone will ask: "Restore all original phone settings? Phone will restart." Press 'Yes' and enter your Lock code (default is 12345).Tip: Formatting takes several minutes so you'd better connect your Nokia 3650to a charger to ensure that your battery doesn't get empty in the middle of formatting.Note: All your created acces points and mailboxes will be lost so take a note of them. And all application settings will be reset.E.g. In Camera, image quality is set back to normal and memory in use is set back to phone memory. And also in Messages,memory in use is set back to phone memory, etc. Also backup your contacts with PC Suite or a program like Contacts Manager.
To reset your wallet, should you forget your code,
Type in:*#7370925538#
this will reset the wallet code, the wallet contents will be deleted.
How to free more RAM on your phone
>>> Method 1: Flight mode:
Put your phone in "Flight mode" with Psiloc System Tools. Install System Tools, open it and select "Flight mode". This way you can restart the phone without your SIM card so there will be no running phone tasks in the background. Now you can have up to 3,5 MB of free RAM!
Note: ironically enough, Flight mode doesn't work when Smart Launcher is installed, at least in my case. But i've also heard several reports of people who have both apps running without any problems.
>>> Method 2: Smart Launcher trick:
Install Smart Launcher and open it. Go to Options, Settings and put Launcher ON.Now plug in your charger and switch off your phone. Wait untill the battery meter appears and short press the Menu button (don't hold).The menu should appear and now you can have 3,5 to 4,5 MB free RAM! (Hold Menu button to check RAM).
The trick is that with the charger plugged in, the phone must get a minimum software support for charging, even whenthe phone is switched off. And somehow Smart Launcher has still got it's shortcut running and that's the Menu button. So whenyou press the Menu button, you go directly to the Menu without any other phone tasks running in the background soyou trick the phone and you have more free RAM!Note: when you unplug the charger, the phone will switch off.
>>> Method 3: Menu :
This method I found it by myself, it frees a little about 100~200 KB but I guess it's useful sometime
Close your menu not by selecting the right selection key "exit", or pressing the menu key another time, they only hide the menu app but do not close it, to close it select the left selection key "option" and scroll down and select "exit"
So when you open an app needs more ram reopen menu and close it, it's useful when play low bit rate video in realplayer paradis.
